Vortex flow sensor, 1–16 L/min (0.06–0.96 m³/h)
Port sizes G1/2, G3/4, G1; ranges up to 150 L/min
Flow and temperature switching outputs, dual display
IO-Link Class A, M12 A-coded 4-pin connector
TFT colour display, four viewing directions
NPN/PNP/push-pull, NO/NC, 12 bar, IP65

Ask for a price

The FMVH-016-IOL-G12 is a vortex flow sensor for water in pipes. It measures flow and medium temperature in one housing, shows both on a TFT colour display, and switches two outputs that can be assigned to either value. The electrical side is a single M12 A-coded connector carrying 24 VDC and an IO-Link Class A interface.

A bluff body in the flow path sheds vortices at a frequency proportional to velocity — the von Karman vortex street — and the electronics turn that frequency into litres per minute. Switch point, reset point, hysteresis or window mode, NPN/PNP/push-pull and normally open or closed are all set from the three front buttons, and the display can be turned to four viewing directions. An accumulated flow counter adds up the volume since power-up; it is intended for reference and resets when the sensor is switched off. Depending on the upstream fitting, the sensor needs 15–50 DN of straight pipe before it and 5 DN after it.

The G1/2 female thread carries 1–16 L/min. The same sensor is built in five ranges up to 150 L/min with G1/2, G3/4 and G1 ports, so dosing lines and cooling circuits can be covered by one family. Wetted parts are ETFE, PA6T and 304 stainless steel, the body is rated 12 bar continuous and 18 bar maximum, and IP65 allows installation in machine tools, water treatment and process cooling. Ambient range is −10 to 65 °C.

ModelFMVH-016-IOL-G12
Operating voltage24 VDC ± 10 %
Operating current< 100 mA
Ambient temperature−10 … 65 °C
Ingress protection ratingIP65

Flow parameters

Measured mediumWater
Measuring range1–16 L/min (0.06–0.96 m³/h)
Flow accuracy< 3.0 % F.S.
Accumulated flow range99 999 L or 99 999 m³ (resets after power-off; for reference only)
Wetted materialsETFE / PA6T / SUS 304 stainless steel
Process connectionG1/2 female thread
Pressure rating12 bar; maximum pressure 18 bar
Real-time flow unitL/min or m³/h, selectable by button
Switching output typeNPN/PNP/push-pull, NO/NC, hysteresis/window, programmable
Switching output current250 mA
Switch point SP setting range1.2–16 L/min
Reset point rP setting range1–15.8 L/min
Minimum separation between SP and rP0.2 L/min
Switching output resolution0.1 L/min

Temperature parameters

Measuring range0–100 °C
Temperature accuracy1 °C
Display unit°C or °F, selectable by button
Switching output typeNPN/PNP/push-pull, NO/NC, hysteresis/window, programmable
Switching output current250 mA
Switch point SP setting range1–100 °C
Reset point rP setting range0–99 °C
Minimum separation between SP and rP1 °C (1 % F.S.)
Switching output resolution0.1 °C

IO-Link

Number of interfaces1
IO-Link protocol versionV1.1
IO-Link interface typeClass A
Frame typeTYPE_2_V
Transmission rateCOM2, 38.4 kbit/s
ISDU (indexed service)Supported
Block parameter operationNot supported
Data Storage (DS)Supported
Minimum cycle time3000 µs
Data storage lockSupported (for compatibility only; the device does not execute this operation)
Vendor ID1317 (0x0525)
Device ID198162 (0x030612)

Available measuring ranges and port sizes

Model codePort sizeMeasuring range
016G1/21–16 L/min
040G1/22–40 L/min
070G1/23.5–70 L/min
100G3/45–100 L/min
150G19–150 L/min
FMVH-016-IOL-G12 dimensions in mm

RELATED PRODUCTS

MF4700 Gas Mass Flow Meter

MEMS thermal mass flow meter, NPT or BSPT
Maximum overflow 6 to 2000 SLPM by model
Accuracy ±(2.0+0.5FS) %
Analog 0.5 to 4.5 Vdc or 4 to 20 mA
RS485 Modbus half-duplex output
IP40 body, AMPMODU MTE or M8 connector

MF4600 Gas Mass Flow Meter

MEMS thermal mass flow meter, DN1 to DN8
Maximum overflow 2 to 200 SLPM by model
Accuracy ±(2.0+0.5FS) %
Analog 0.5 to 4.5 Vdc or 4 to 20 mA
RS485 Modbus half-duplex output
IP40 body with manual keypad control

MF4500 Gas Mass Flow Meter

MEMS thermal mass flow meter, BSPT inline
MF4512 100 to 300 SLPM, MF4519 500 to 1000 SLPM
Accuracy ±(2.0+0.5FS) %
Turn-down ratio 50:1
RS485 Modbus half-duplex output
IP40 body, BSPT 1/2 and 3/4 inch connections

MF4000 Gas Mass Flow Meter

MEMS thermal gas mass flow meter
Full scale 2 to 50 SLPM (MF4003 / MF4008)
Accuracy ±(1.5+0.15FS) %
Turn-down ratio 100:1
Analog 1 to 5 Vdc plus RS485 / RS232 / I2C
IP40 body, BSPT or 4 / 6 / 8 mm one-touch

RELATED PRODUCTS